Electrode Relay

Overfill Cut-Out Device According to § 19 WHG

Part No. ER-107/B

For level switch

Limit level detection of conductive liquids, a measurement systems consists of a double rod electrode and an ER-107 relay

Description
  • Overfill cut-out device according to § 19 WHG
  • Slimline construction, width only 22.5 mm
  • Adjustable sensitivity
  • Potential-free output as SPDT (2 x)
  • Power supply 230 V AC ±10% 48-62Hz, 24 V DC ±10%  (optional)

Construction

The overfill cut-out device consists of the pickup (conductive double electrode) and the electrode relay type ER-107. It provides a binary switching signal at the out-put. This signal can be sent directly or via a signal amplifier to the report device or to the control section and its control element. The overfill cut-out device's components which have no test certificate have to correspond with the sections 3 and 4 of the device's approval principles (ZG-ÜS).

Function

The electrode relay ER-107 provides a measurement voltage which makes a "working current" flow through the signal wire via the built-in resistor in the pickup. As soon as this working current is interrupted (e.g. cable break) this is detected and displayed by the ER-107 and the source contact switches to alarm status. When the filling level of the container reaches the conductive pickup's rods a measurement current is able to flow through the conductive liquid. This current, which is higher in comparison with the working current, is detected by the ER-107 and the alarm message is generated.

The sensitivity can be adjusted within the response range of the probe using a potentiometer.

The ER-107 functions are based on the closed circuit current principle. The alarm status of the relay corresponds with the dead condition of the device.

Hence, beside monitoring and reporting of wire interruptions and level increase up to the pickup's point of response, the ER-107 also monitors working current failures.

The conductive double rod electrode has a G1½" connection thread as standard.

Technical Data
Common
Storage temperature

-30 °C to +80 °C

Operating temperature

-20 °C to +90 °C

Enclosure

Screw joint and head: PPH (Polypropylene)

Coating: Polyamide

Connection thread G 1½”

Pressure 10 bar

 

Rod material

stainless steel (1.4571)

Rod diameter

4 mm

Rod length

300 mm

Double rod electrode according to §19 WHG
ER 107/B
Outputs

- Contacts: 2 potential-free SPDTs (simultaneously operated)

- Max. switching voltage: 250 V AC; 150 V DC

- Max. switching current: 5 (3) A AC; max. 5 A DC

- Switching capacity 1: 250 VA DC; 50 to 180 W DC (depending on switching voltage)

Inputs

- Open circuit voltage: <10 V AC

- Short circuit current: <5 mA

- Switching delay approx.: 0.5 s

- Sensitivity range: 1 to 30 kOhm

 

Display

2 LED zur Signalisierung von Betrieb, Leitungsfehler und Alarm

Z-65.13-405, Z-65.40-191

Storage temperature

-30 °C to +80 °C

Operating temperature

-20 °C to +60 °C

Enclosure

- Weight: approx. 150 g

- Protection: terminals IP20, enclosure IP40

 

Power consumption

1 VA

Power supply

230 V AC ±10 % or 24 V DC ±10 %

other voltages on request

 

Specifications subject to change.

Downloads

Data Sheet Overfill cut-out Device acc. § 19 WHG

Overfill cut-out Device acc. § 19 WHG – electrode relay and conductive probes

Accessories
Related Products

Haven't found the appropriate product?

Product Consultation

You want to have best information about our products? Our experts will gladly develop together with you the best system solution for your application.

Service

You have questions about your NIVUS products in use? Our service hotline will readily support you.

Hello
We are glad to have you here! For any question regarding water or digitisation we are happy to answer you call or your email message.
Team NIVUS
Im Täle 2
75031 Eppingen